250M EXTEND PoE Kit for 8x Raspberry Pi B/B+/2/3 Micro USB 5V 2.4A /Switch 8 PoE

Description

Power Over Ethernet Kit for 8x
Raspberry Pi
(250M 8ports PoE Switch+ Micro USB PoE Splitter)
for Raspberry Pi B/B+/2/3
Support
EXTEND mode
, max Network Cable length to
250 meters
NOTE. When
EXTEND mode enable
, the Max bandwidth for the
Power Link (PoE) port 1-8
network port will be
reduced to 10Mbps for each one
.
(The up-link is not affected, it will always working at 100Mbps max speed)
PoE Switch Specification:
ALL Port:
Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with 4 pairs UTP Cat5/5e/6 cable。
Power Link Port 1-8:
any supported unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs)
Power LED
LED ON: power on. LED OUT: power off
Green Light LINK/ACT
LED ON Indicates the port is connected to a network device and has been started
LED OFF Indicates that this port is not connected to a network device or has not been started
Standard
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3x Full-Duplex flow control
Protocol
CSMA/CD Ethernet
Data Transfer
Rate
Ethernet: 10Mbps (Half Duplex)
20Mbps (Full Duplex)
Fast Ethernet: 100Mbps (Half Duplex)
200Mbps (Full Duplex)
IC Chips
IC Plus IP178G
Network Media(Cable)
10Base-T(EXTEND mode): UTP category 5e, 6 cable (maximum 250m) EIA/TIA-568 100Ω STP (maximum 250m)
100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m)
PoE Power on RJ45
Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8
DC Output: 52V, Per port Max 1A or 50Watt, 8 POE ports Total Max. 120Watt
Number of Ports
10 x 10/100Mbps Auto-Negotiation RJ45 ports with 8 PoE enabled (port-1 ~ port-8)
Power Input
AC Input: 110V ~ 240VAC, 50Hz ~ 60Hz.
DC OutPut: 52V/2.7A
Power Consumption
3.2 Watts (max. no PD connected)
According to the actual power consumption of equipment
Temperature
Operation Temperature:0 ~40
℃
(32 ~104
℉)
Storage Temperature: -40 ~70
℃
(-40 ~158
℉
)
Humidity
Storage Humidity 5%~90% non-condensing, Operating
Humidity 10%~90% non-condensing
Product Dimensions
197mm W x 73mm D x 32mm H
RAM Register Capacity
64K bytes per device
MAC Address List
1K entries per device
Frame Forward Rate
10Mbps Ethernet: 14880pps/Port
100Mbps Ethernet: 14880pps/Port
Notice:
Yellow LED(power) of the splitter will be light up when micro USB connects to the device.
Green LED(data) of the splitter never light in any circumstances,two reasons are below,
1.The splitter does not have the function to monitor the data of the network cable.
2.due to the cost problem,the network interface component is from the universal components which own two LEDs on the market.
PoE Splitter Specification:
Compliant with IEEE802.3af
Isolation: 2.5kV
Power Input:  DC44~57V
Power Output: DC5V 2.4A
Data&Power INPUT Port: from RJ45 female (Compliant with IEEE802.3af/at PoE)
Data Output Port: RJ45 Male
Power Output Port:
Micro USB Power Plug
Data Transfer Rate:  10/100Mbps
Devices will be detected before poe input
Power Pin:support both 1/2(+/-),3/6(-/+) or 4/5(+),7/8(-)
Body size: 80 x 27x 22 mm
DC cable length：165mm
RJ45 Modular Plug cable length：155mm
Weight : 55g
Item Included:
Output 5V 2.4A Active PoE Splitter(Micro USB Power Plug) x8
120Watt 10pots 8PoE Passive PoE switch(
DSLRKIT MID8P2U-E250)
x1
AC power plug is US or EU type,if you need other type (AU or UK),Please leave a message.